Showing results: 1726 - 1740 of 2684 items found.
-
779670-01 -
NI
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
781217-01 -
NI
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
782568-01 -
NI
2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI - The RMC‑8355 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon E5620 quad‐core processors that support up to 96 GB of DDR3 RDIMM ECC RAM. The RMC‑8355 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8355 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
XF07-518 -
Curtiss-Wright Defense Solutions
The XF07-518 is a rugged quad channel 500MSPS 14-bit digital receiver XMC. The ADC devices are controlled by a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms. The combination of direct high-speed, high-resolution analog I/O port and FPGA processing makes the XF07-518 ideal for demanding applications including radar, imaging and test equipment across commercial and defense market spaces.
-
WIKA Alexander Wiegand SE & Co. KG
Hand-helds are portable calibration instruments for mobile use for the accurate measurement and recording of temperature profiles. For the instruments there are various designs of thermometers available. Through this, hand-helds are particularly suitable as test instruments for a large variety of applications in the widest range of industries. Data recorded in the hand-held can be evaluated via PC software, some instruments document calibrations in the internal memory, which can later be read on a PC. Optionally, a calibration certificate can be generated with our calibration software WIKA-Cal.
-
Mensor Corp.
Hand-helds are portable calibration instruments for mobile use for the accurate measurement and recording of temperature profiles. For the instruments there are various designs of thermometers available. Through this, hand-helds are particularly suitable as test instruments for a large variety of applications in the widest range of industries. Data recorded in the hand-held can be evaluated via PC software. Some instruments document calibrations in the internal memory, which can later be read on a PC. Optionally, a calibration certificate can be generated with our calibration software WIKA-CAL.
-
RF Industries
For applications that demand low VSWR, low insertion and low PIM cable assemblies; RFI now offers semi-rigid and corrugated cable assemblies with factory soldered N and DIN connectors. Assembled using the latest soldering equipment for years of performance reliability. Each assembly is tested for insertion loss, VSWR and PIM rating and is shipped with individual test data. Available using flexible or super flexible corrugated cables with a standard or fire retardant jacket.
-
Teledyne LeCroy
Teledyne LeCroy Test Services patented Quick Sensor is a pre-fabricated Torque & Thrust Strain Bridge that is applied to a shaft much the same way as a strain gage. This time-saving device was developed for the Nuclear Power Industry to reduce the time and effort required to install strain gages in a radioactive environment. Since it's introduction in Nuclear Plants, the Quick Sensor has become popular in many other industries and applications where gaging time and cost is a concern.
-
AFX Series -
Pacific Power Source, Inc.
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
ADLINK Technology Inc.
As a leading provider of PXI products in test & measurement market, ADLINK has devoted its extensive field experience to the PXI platform. After more than ten years and developing more than 100 PXI products for automation and testing, and as a sponsor member of the PXI System Alliance, ADLINK continues to expand PXI and PXI Express offerings with innovative products, meeting the unique needs of high-speed and high-bandwidth applications, such as spectral monitoring and signal intelligence.
-
CUT35 -
TDK-Lambda Corp.
The triple output CUT35 and CUT75 power supplies have two independent, isolated, converters, one for the main 5V output, and one for the auxiliary outputs. This topology provides several benefits - no minimum loading, enhanced load & line regulation and the ability to connect the auxiliary outputs in series to generate either a 24V or 30V output. This flexibility makes it suitable for use in a wide range of process control, broadcast, test & measurement, medical and industrial equipment applications.
-
Mors Smitt Group
Mors Smitt manufacture the full range of British Rail equivalent relays including AC & DC coils, instantaneous, gold contacts, safety critical, push to test relay button, timer/time delay, and flashing. These relays can be found throughout Rolling Stock vehicles including locomotives, diesel multiple units (DMUs), electric multiple units (EMUs) and light rail trams. Applications include circuits involved with lighting, doors, brakes and alarms.
-
WTX-610 iLLUMINATOR -
Consultix
Wideband operation up to 6 GHz allows the iLLuminator to address all your future needs of signal generators / test transmitters even over unlicensed bands for LTE-U and LAA or the CBRS Band. These features combined with the ultra-portable handheld form factor and innovative touch interface for maximum ease of use make the WTX-610 iLLuminator a convenient choice for laboratory users as well as field applications such as DAS & Small Cells radio planning and testing.
-
60-106-001 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 60-106-001 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. The chassis features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.This chassis is also available with built-in scan list sequencing and triggering (model 60-106-002).
-
Shimadzu Corp.
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics. ASTM D638 specifies methods for testing the tensile strength of plastics and other resin materials and for calculating their mechanical properties, and outlines accuracy requirements for the test frames and accessories used.
